MenuSearch | Country: Canada | Currency: CAD
TY-14013R Ultra-thin 140mm PWM Fan
Discontinued
More variations available Show

Thermalright TY-14013R Ultra-thin 140mm PWM Fan

The Thermalright TY-14013R 140mm fan uses 120mm fan mounts and is only 13mm thick, ideal for when space is at a premium.

Features

  1. Ultra-thin, only 13mm thick
  2. Enhanced Hyper-Flow bearing
  3. Minimum noise only 21.7dB(A)
  4. Maximum airflow 64.5 CFM
  5. 4-pin PWM connection

The fan design of the TY14013R corresponds to the desire of users to realise the greatest possible airflow at the lowest possible noise. Naturally fans with a larger diameter will produce higher air-flow at the same speed and/or the same noise level than smaller fans. Despite its particularly flat design the TY 14013R offers an airflow of more than 65 CFM.

The Thermalright TY 14013R has the dimensions 140 x 152 x 13 mm; the mounting points are identical to those of conventional 120mm fan. Due to its sophisticated design, the inner diameter of the fan is even slightly greater than that of a conventional 140mm fan. The TY 14013R is the ideal case fan for compact HTPC cases. Please check sufficient space is available around the fan.

The speed range of the temperature-controlled PWM-fan is 700 - 1300 RPM which provides flow rate between 35.3 and 65.3 CFM. For very quiet operation the model uses seven blades in a special “torpedo” design and thanks to the optimised wings and streamlined frame design, the fan is effective and at the same time produces extremely quiet wind noise.

In order to guarantee a long-term low-noise operation, Thermalright makes use of a low-wear “Enhanced Hyper-Flow” bearing. The monitoring and control of the fan speed is done via the motherboard’s PWM function.

SpecificationsTY-14013R 140mm PWM
Dimensions140 x 152 mm
Depth13 mm
Voltage Range~ 6 - 13 V
Fan Speed700 - 1300 rpm
Air Flow35.3 - 64.5 CFM
Noise21.7 - 30.6 dB(A)
BearingEnhanced Hyper-Flow Bearing
Connector4-Pin PWM
Warranty24 months
EAN barcode0814256000871
SpecificationsTY-14013R 140mm PWM
Dimensions140 x 152 mm
Depth13 mm
Voltage Range~ 6 - 13 V
Fan Speed700 - 1300 rpm
Air Flow35.3 - 64.5 CFM
Noise21.7 - 30.6 dB(A)
BearingEnhanced Hyper-Flow Bearing
Connector4-Pin PWM
Warranty24 months
EAN barcode0814256000871

Product Resources

FAQ

  • How do I measure fan size?

    The size of fan you need will generally be determined by the size of the fan fitting position in your PC case. The sizes of all the fans on our website are shown as measured along any one of the fan’s four sides, NOT the distance between the fan’s screw holes! Our most popular fan size is 120mm, followed by 80mm. This isn’t really dictated by customer preference, but more by recent designs of PC cases.

    As for the thickness (depth) of the fan, generally 25mm (1 inch) is by far the most common depth, although smaller fans can have shallower depths such as 15mm or even 10mm. All our fans are 25mm thick unless otherwise stated. If you have any questions about which fan you should order, please don’t hesitate to get in touch.

    If you know the distance between the fan mounting screw holes but don’t know what fan size to order, please see the following table. Note that the mounting hole measurements shown below are taken horizontally or vertically between the holes and not diagonally.

    Screw hole spacings and fan sizes

    Space Between Screw Holes Fan Size
    32mm 40mm
    40mm 50mm
    50mm 60mm
    60mm 70mm
    72mm 80mm
    83mm 92mm
    105mm 120mm
  • I received a small cable (resistor) with my fan; what is it for?

    The resistor cable (also called Ultra Low Noise or ULN cable) is designed to allow the fan to run slightly slower for even quieter operation. The benefit in lower running noise is significant. Although the airflow will be reduced slightly, this usually has minimal effect on PC temperature. We would generally recommend using the ULN resistor cable for best results in almost all circumstances.

  • How can I tell which way the air blows through the fan?

    Hold the fan so that the round fan sticker is facing you. You are looking at the rear of the fan. When you plug the fan in, the air will be blowing towards you. If you want a fan to act as an air intake, then the fan sticker will be facing the inside of the case. Some fans also have two small arrows moulded into their plastic housing - one arrow shows the direction of airflow, and the other (at 90°) shows the direction of blade rotation.

  • Is it possible to use a 4-pin PWM fan or CPU cooler with a motherboard which has only 3-pin fan headers on it?

    Electrically, there is no problem doing this - the fourth pin on the fan cable is used purely for PWM control and is not needed in order for the fan to run. So you can plug the 4-pin fan connector onto the 3-pin motherboard fan header, leaving the fourth pin not connected to anything. The fan will potentially run at full speed, so if you would like to reduce the speed of the fan you will need to adjust the fan speed setting in your BIOS or use fan control software such as SpeedFan in Windows.

    The only other problem to consider is that occasionally, components immediately adjacent to the motherboard fan header can get in the way of the larger 4-pin fan connector, physically preventing connection. This problem also occurs if you try to use an in-line fan speed controller such as the one made by Gelid.

    Another avenue to explore is the possibility of using a bay-mounted fan controller. Several models are available now which provide 4-pin fan headers, so this is an easy way to use 4-pin PWM fans in a PC system which has only 3-pin fan headers on its motherboards. When using this method, you may find it necessary to disable any fan warning settings in your motherboard BIOS, since the motherboard may incorrectly believe that its CPU fan has failed when the fan is connected to a fan controller rather than directly to the motherboard itself.

Top Quiet Fans

Recently Viewed Products