MenuSearch | Country: Canada | Currency: CAD
FANMATE 2 Variable Fan Speed Controller
Discontinued
More variations available Show

Zalman FANMATE 2 Variable Fan Speed Controller Ultra

The FANMATE 2 product is included with the many of Zalman’s CPU coolers and the feedback has been so good that we are now offering it separately for customers who wish to use it with other fans. The FANMATE 2 is connected in-line with an existing fan and allows infinite control over the speed at which the fan runs. Where a fan is making a lot of noise due to excessive airflow, this can be reduced in a controlled manner, until such point as the noise becomes minimal and the airflow still adequate. The silencing effect of reducing the speed of a fan even by a small amount can be very surprising!

The FANMATE 2 has a small rotary knob which can be turned in either direction, to raise or lower the fan speed. Once you are happy with the noise/airflow setting, just leave the knob set in its position and your installation is finished. The best approach is to start with the FANMATE 2 at its minimum speed setting (“silent mode”) and then increase the speed if more airflow is required.

Rather than using a simple rheostat (variable resistor) arrangement, the FANMATE 2 uses a high quality variable voltage regulator circuit which will not wear out or run excessively hot. Full instructions are supplied, and installation is very easy as can be seen in the diagram below. The product is intended to be used primarily with case fans, and you may be surprised how reducing the speed of a case fan (even slightly) can have a very large effect on noise output, with only a minimal effect on airflow. Of course the best approach is to use fans which are quiet to begin with, but if this is not possible, the FANMATE 2 will provide a very satisfactory alternative in your quest to reduce noise.

Although using the FANMATE 2 in conjunction with the fan on a CPU cooler is certainly possible, you would need to be careful to ensure that the processor does not get too hot due to inadequate airflow. If you have a CPU heatsink which is thermally inefficient in its design, then its manufacturer may have compensated for this shortcoming by providing it with a high-flow high-noise fan, usually because fast fans are cheaper than good heatsink designs! Using the FANMATE 2 in this scenario is not a good idea, and if budget allows, we would always recommend replacing the whole CPU cooler with one of the coolers we sell. This will guarantee safe cooling with the minimum possible noise level.

Please note that you must not use the FANMATE 2 in conjunction with any 12 volt fan having a power consumption in excess of 6 watts, or 0.5 amps. Damage to the fan and/or Fan Mate and/or PC system could otherwise occur. Virtually all but the very fastest/most extreme airflow fans consume under 6 watts and are therefore fine, but please check your fan specification before using the Fan Mate if in any doubt.

Finally, when using the FANMATE 2 at its minimum speed setting, you must ensure that the fan has a minimum startup voltage specification of not more than 5 volts. Otherwise, the Fan Mate will not give a high enough voltage to get the fan started from rest. Before finalising your installation, please test that all FANMATE 2-connected fans successfully start when you first power on the system. If you are using the FANMATE 2 with any of our Ultra-Quiet fans, you do not need to worry about this point because all our Ultra-Quiet fans are guaranteed to start at 5 volts.

SpecificationsFANMATE 2
Dimensions70 x 26 x 26 mm
Wire length800 mm
Weight20 g
Output voltage5-11 VDC +/- 2%
Maximum allowable fan wattage6W or lower
Warranty24 months
EAN barcode8809213761072
SpecificationsFANMATE 2
Dimensions70 x 26 x 26 mm
Wire length800 mm
Weight20 g
Output voltage5-11 VDC +/- 2%
Maximum allowable fan wattage6W or lower
Warranty24 months
EAN barcode8809213761072

Customer Reviews

Zalman FANMATE 2 Variable Fan Speed Controller

,

Bought this one couple of years ago. Still working like a new. Very good quality and service from QuietPC.

Works great, only a slight gripe.

,

Does exactly what it says on the tin, my only problem with it is that even set to maximum the fan isn’t at full speed. My Noctua 80mm has a max speed of 1800rpm which it was producing more or less dead on before I fitted this, now it maxes out at 1500rpm. It would be nice to be able to run it at full speed should I ever need to.

Nice

,

Always feels like there’s not enough range to operate. You never know what voltage fan is using right now. Other then that it’s a nice gizmo.

Bought 4 of these as recommended by andy

,

Installed 4 of these in my small HTPC case.

Pros:

  • cables are too long rather than too short (cable tied).
  • very simple to set up and use.
  • cheap.

Cons:

  • you have no idea what voltage the fan is using.
  • think the rotary dial should be exchanged for a 5,7,9 or 11 volt switch.

All in all very useful for getting fans to spin slower to make them much more quiet.

Great little product

,

A doddle to install. For less than £4 you get complete control of your CPU fan speed. The only tiny issue was that it comes with miles of cable to let you position the controller outside your case (it even has a sticky pad to allow easy fixing). An elastic band tidied up the cable and it’s great. I expected nothing less from THE BEST CUSTOMER SUPPORT COMPANY IN THE WORLD! If Andy at Quiet PC recommends something that’s good enough for me.

Simple, cheap, effective

,

Simple, cheap, effective. Not pretty but you’re not going to see much of it so that doesn’t matter, does the job you need.

Brilliant!

,

Does the job superbly.

FAQ

  • The cooler I purchased came with a variable fan speed controller. How do I know what speed to run the fan at?

    When you first install your new CPU cooler we recommend that you run its fan at full speed to ensure that everything is working properly and the PC boots successfully. Then you can turn the speed controller’s knob down to its minimum setting and appreciate the difference in noise level! Most people prefer low noise rather than maximum cooling for everyday computing, so clearly it makes sense to turn the fan speed controller to its minimum setting and see how it goes.

    If you are running your PC in a particularly hot environment, or if you are experiencing stability issues then try turning the speed up slightly for more cooling. Generally speaking, virtually all the coolers we sell will adequately cool any modern processor at their minimum fan speed setting. However, if you want to be 100% sure that your CPU is in no danger of overheating, then you can check its temperature in the BIOS setup (press Del or F2 etc. when you first switch your PC on, then look for the CPU temperature reading in “Hardware monitor” or “PC Health Status” option or similar).

Top Fan Accessories

Recently Viewed Products